Recent content by prestonztt

  1. P

    Other forums

    My first forum was 300zxclub.com, I joined back in like 2004. I sure do miss my TT 300zx :(
  2. P

    ATE Super Blue is no more

    They still have it on eBay floating around for about $20 shipped.
  3. P

    Members YouTube ID's !

    My Channel: prestonztt
  4. P

    '06 WRX - Built 2.5, Precision 6262, E85, Etc - 570whp @ 23psi

    Event: Dyno Tune Location: Abel Racing Ambient Temp: 90 Degrees Elevation: +250 Weather: Sunny Car: '06 WRX Tuner: Andrei Mitine Dyno Info: DynoJet Transmission: PPG 5 Speed Dogbox Gear: 4th (1:1) Peak HP at RPM: 578whp Target Boost: Spiked to 26 psi, then dropping to 23 psi Target AFR: 12.2...
  5. P

    Private Community?

    If a person is willing to pay $69 then they are more then likely going to contribute and use the board. If not, then easy money was just made :)
  6. P

    Private Community?

    Even though I haven't been on this board long at all, I can tell you there is a real good group of people on this board. Everybody I have dealt with have been more then willing to lend a hand and just be helpful in general. What I have seen from being a moderator on a local board here in...
  7. P

    Drink of Choice?

    Patron and 7-Up. It is ridiculously good!
  8. P

    Clutchmasters FX500 + ACT Streetlite Flywheel ('06-'11 WRX/LGT/Baja)

    Up for sale is my Clutchmasters FX500 Clutch and ACT Streetlite Flywheel. It will also come with the alignment tool, throw-out bearing, and pilot bearing. There are roughly about 1000mi on the components. The clutch and flywheel were never launched or driven hard. I was breaking in the clutch...
  9. P

    GR RDKLSTi ? 518whp/492wtq (MD) 2008 STi

    If the sleeves dropped, throw that block in the trash or make it a nice coffee table :) It will continue to blow headgaskets no matter what you do to that block. One reason sleeves drop are due to the supports in the bottom of block not being cut properly; making the sleeves shift, move...
  10. P

    Speed density, stalling out, sick of it.

    What fuel are you using again? or did I miss that somewhere in this thread? Lol Is it a lean studder or is it rich when it does it? Any boost leaks? Are all the grounds hooked up? I would try tightening up the gap on the plugs to around .022. Coilpacks would be a good thing to swap out aswell.
  11. P

    Last page?

    Same thing has happened to me a few times aswell. I even tried different browsers and it still did the same thing.
  12. P

    Chuggish cold start idle, Dying when coming to a stop/revving, Etc (OpenSource SD)

    Car is a 2006 WRX. Mods are: Built Motor Rotated Kit w/ Precision 6262 Turbo Crower 272 Cams BC Springs and Retainers Five-0 Motorsports 1400cc Injectors Twin In-Intake Fuel Pumps AEM AFPR '07 2.5i Intake Manifold GM IAT Omni 4-Bar Map Sensor E85 No mechanical problems whatsoever, no boost...
  13. P

    Bypass/Delete 4EAT TCU?

    They were Exedy Carbon Triple Discs. It just seemed after driving the car hard for about 2000 miles, the discs would kind of weld themselves to each other and have engagement problems. Did some research and that is one of the problems with the Exedy's. If I can hook the TCU up rather easily, I...
  14. P

    Bypass/Delete 4EAT TCU?

    Its not so much an awkward swap, just a lot of people don't do it. If you have ever been in a fast boost auto car, you will know why I want to do this. It's ridiculous how much different a fast auto car feels from a fast manual car. I don't mind the auto being in manual mode all the time. The...
Top