Search results

  1. J

    Oil Feed Line Install Problems On Blouch Dom 1.5XT-R

    It is absolutely flat. I just reused the copper washer. I will try to call Subaru and get two more washers. Where do I put the washers maybe I'm putting them in the wrong spot?
  2. J

    Oil Feed Line Install Problems On Blouch Dom 1.5XT-R

    I'm having a problem with my oil feed line with the same turbo. right where it connects to the motor it keeps spraying out pretty bad. I wasn't sure if I had to hole in the bolt aligned correctly. I tried having the holes lined up with the feed line and I also tried them not aligned it sprays...
  3. J

    help Exhaust Housing

    Thanks guys appreciate your help she's all good!:tup:
  4. J

    help Exhaust Housing

    Coolant
  5. J

    help Exhaust Housing

    do you know how long that court line is am I going to have to weave in and out of the things or is it pretty shortbecause the 1 for myNew turbos braided it's real flimsy which is nice.
  6. J

    help Exhaust Housing

    yeah I think that's what it is my Dom 1.5 came with a line that is supposed to connect to that right ??I'm screwed
  7. J

    help Exhaust Housing

    where the elbow is its pinched and dented. to tight to take a picture where that is . but thats my problem ^^^^
  8. J

    help Exhaust Housing

  9. J

    help Exhaust Housing

    I will get a picture
  10. J

    help Exhaust Housing

    No where my 10cm hot side connects to
  11. J

    help Exhaust Housing

    Where my hotside connects to.
  12. J

    help Exhaust Housing

    I have an 11Sti I'm swapping out the turbo for a better up grade and i bent / pinched the Exhaust Housing since its like tin. What do I do? :(:(
    • jjv
    • Thread
    • Replies: 19
    • Forum: Engine
  13. J

    Work xd9

    Thank you for your help but all of that is just over my head i have a hard time comprehending all of this. The two rims i have an options of choosing from are these. 18x9.75 is with a +20 offset. And the 18x8.75 is with a +35 offset. I will be lowering a little with fortune 500 series coils...
  14. J

    Work xd9

    I have changed my mind xxr 527
  15. J

    Work xd9

    I have an 11 sti looking to purchase work xd9. Don't know what offset to buy to make them flush with my car. Any body familiar with wheels? I wanto keep the big dish don't know anyone who can roll fenders though. Either want 18x9 or 18x10. Can anyone help?
  16. J

    blouche dom 1.5 xtr

    Went with the 10cm
  17. J

    issue with tpms with aftermarket wheels

    What should I do to get the light off whenever i put aftermarket wheels? Can I get the light off ? Or deal with the light?
  18. J

    power difference from UEL and EL header

    I heard an sti tonight with the EL. honestly o think it sounds very good and I'm keeping my EL.
  19. J

    power difference from UEL and EL header

    Yeah I didn't do to much research. I have an 11 sti catless invidia back to single exit. Just purchased a bigger top mount. 1000cc injectors . Fuel pump. Blouch dominator 1.5. Ebcs. I am afraid to lose the subaru rumble because I bought the invidia race. But if its only a few HP . I minds well...
  20. J

    power difference from UEL and EL header

    Is there a big power difference from UEL and EL header? Bought an EL invidia race with uppipe. Worried about sound and mighy try to sell it for UEL. big power difference?? Any suggestions?
    • jjv
    • Thread
    • Replies: 12
    • Forum: Engine
Top