Silver Bullet 2004 WRX STI

[Raven32]

So next question I have for you [MENTION=9]HolyCrapItsFast[/MENTION], is what size injectors should I be looking for. Currently running tomei headers, deadbolt 20g td06, stock cams. Internals are stock crank, Manley I-beams and manly 612000cb-1 Pistons. Also have 255lph fuel pump already installed. Right now have the stock side feeds in there.


Sent from my iPhone using Tapatalk

 

[Raven32]

Ok so rotating assembly won't be done till Tuesday with balancing. So what's an Anxious person to do?


Paint his headers to protect against the elements.


Start off by wire wheeling the bare metal to Remove any surface rust and other contaminants. Then clean all surfaces with lacquer thinner to remove all oils. Followed off by masking off all the gasket areas.

Hang up parts so that it is easy to apply paint on all surfaces.

Then apply 4 coats with 10 minutes in between each coat, as per instructions on can.

Sent from my iPhone using Tapatalk

 

[Doppelganger]

Looks good

A goal is not always meant to be reached, it often serves simply as something to aim at. (Bruce Lee)

 

[Raven32]

Look what I found on craigslist

Sent from my iPhone using Tapatalk

 

[Doppelganger]

Are you going from side feed to top feed now?

It's why I've invested money in to the porting equipment I've ordered or am ordering.

A goal is not always meant to be reached, it often serves simply as something to aim at. (Bruce Lee)

 

[Raven32]

yes i plan to go from side feed to top feed setup. I also plan to do a TGV delete mod. Basic tools will be used.

Hand saw to make initial cut on the aluminum, and then die grinder with various bits to smooth it out. Finally gonna use some aluminum brazing rods to fill the wholes, and re-smooth.

link to the rods can be found here.
http://www.homedepot.com/p/Bernzomatic-AL3-Aluminum-Brazing-and-Welding-Rods-334491/203710179

As I don't think my intake will ever reach anywhere near 700*F, it should not be an issue.

 

[Raven32]

Also found this Defi gauge pod for center console.

Sent from my iPhone using Tapatalk

 

[Raven32]

Ok some kid project updates.

Will fill in info for those that want it later.


Sent from my iPhone using Tapatalk

 

[Doppelganger]

These are going to be the gaskets that I use to port match the intake manifold and TGV Housings.

A goal is not always meant to be reached, it often serves simply as something to aim at. (Bruce Lee)

 

[Raven32]

I am just using OEM for now as I can always remove more material later.

Sent from my iPhone using Tapatalk

 

[Doppelganger]

Looking good how many hours you have of port work done to them and are you going to do the intake manifold as well

A goal is not always meant to be reached, it often serves simply as something to aim at. (Bruce Lee)

 

[Raven32]

I have about three hours on this one TGV. Mostly because first one and going slow, as I don't know the thickness of the metal and don't want it to be too thin.


Sent from my iPhone using Tapatalk

 

[Raven32]

Also 24hrs later...

Sent from my iPhone using Tapatalk

 

[Raven32]

Fk.... There goes $60

Something fell in while putting rod together right after I cleaned it.



Sent from my iPhone using Tapatalk

 

[IGOTASTi]

Ouch. ?

?Ask us how to become a Lifetime Platinum Member today!?

 

[Raven32]

Hmm look what I found at my door today.

Sent from my iPhone using Tapatalk

 

[Alin]

Who in their right mind would leave such a thing at your doorstep?!?!!? :lol:

 

[Raven32]

USPS


Sent from my iPhone using Tapatalk

 

[Doppelganger]

They messed up my shipping address I'll give you the correct info and kindly pay the cost of shipping.

A goal is not always meant to be reached, it often serves simply as something to aim at. (Bruce Lee)

 

[Raven32]

Lol...


On another note.

Rotating assembly is done and sealed

Sent from my iPhone using Tapatalk