Recent content by JuanSTI

  1. JuanSTI

    JuanSTI 06

    so got my car back and it was tuned conservatively since my block is going out did 317 whp and 320 wht on 18psi. starts boosting at 4200 and it feels great really like the tomei arms m7960 very nice turbo. well i guess now i gota start saving for a fully built block.
  2. JuanSTI

    WHAT PARTS CAN BE AFFECTED IF AN ENGINE BLOWS OR JUST GOES BAD ?

    i bought the bosch one its my first time using it too.
  3. JuanSTI

    WHAT PARTS CAN BE AFFECTED IF AN ENGINE BLOWS OR JUST GOES BAD ?

    im was just asking because my car is done and ready for the tune but my friend still thinks the oil pressure is to low its about 12-14psi on warm idle. he thinks i need a new short block.and he says i should drive it till it goes. ive read that 14psi warm idle is normal. i guess what i really...
  4. JuanSTI

    WHAT PARTS CAN BE AFFECTED IF AN ENGINE BLOWS OR JUST GOES BAD ?

    JUST WANTED TO KNOW HOW MANY PARTS WILL HAVE TO BE REPLACED IF THE ENGINE BLOWS OR JUST FAILS TO RUN PROPERLY?
  5. JuanSTI

    Oil Pressure on start up

    my oil pressure is 80-85 cold start and 12-14 warm idle and 64-66 at 6000 warm rev i have mobile 1 full syn 5w-30 and bosch filter
  6. JuanSTI

    This one guy says i dont have to tune headers when i get them???

    so this is pretty much what i got - Tomei Arms M7960, TBE, GS Extarnaly gated uppipe, Tial MV-R Wastegate 44mm, GS Crosspipe (Stock manifolds not pnp'd yet), Manual Boost Controller, Perrin Inlet, KSteck short ram, 850cc injectors, 255lph walbro fp, TGV Deletes, Mishimoto Aluminum radiator with...
  7. JuanSTI

    This one guy says i dont have to tune headers when i get them???

    so i was talking to this guy and i was telling him that i my car was gona be fixed soon but i was gona wait on tuning it till i got the money for some headers and he told me that i didn't have to wait and i could tune it and then install the headers and it would matter. he said the only things...
  8. JuanSTI

    PROVA O SHAPED OR PROVA D SHAPED STEERING WHEEL?

    yea your right. i found this site that will redo my steering wheel ill have to call them tomorrow and see how much it is to do it. is just that i want some more padding and i dont like the leather feel i want some suede or alcantara if they got it you know but if it over 200 ill just leave it as...
  9. JuanSTI

    PROVA O SHAPED OR PROVA D SHAPED STEERING WHEEL?

    WONDERING IF I SHOULD GET O OR D SHAPED STEERING WHEEL. I REALLY NEED IT EVEN THOUGH ITS LIKE 760.
  10. JuanSTI

    wide body front fender ???

    sorry i forgot to say rear driver side and i think it might be the bearing. well for struts/shocks and springs or coilovers, id go with whatever would be better for my car, havent done any research on this so i prob should. for the fender, there aint many trust worthy shops around here ill...
  11. JuanSTI

    wide body front fender ???

    well i was thinking about it just cuz my driver side fender has a pretty bad dent. but ill just go with an oem one, i just got an oem hood for 233. but you guys are right, if im goin to spend money, ima spend it on stuff that makes my car run better. being that u brought up sway bars does it...
  12. JuanSTI

    wide body front fender ???

    you guys think i should get these fenders? http://www.bodykits.com/Extreme-Dimensions/Fenders/Subaru-WRX-Duraflex-GT500-Wide-Body-Front-Fenders-_-2-Piece-_-107272/896411/
  13. JuanSTI

    I NEED HELP ON WHAT ELSE TO GET THAT'S NOT INTERNALS PRETTY MUCH !

    would it be better to get full headers instead of just the gs crosspipe and if so im going with the xcceleration 4 into 1 uel headers they say ill make 25whp and 30whtq i really hope so.
  14. JuanSTI

    I NEED HELP ON WHAT ELSE TO GET THAT'S NOT INTERNALS PRETTY MUCH !

    So iv'e been waiting a long time for my car and as i hear it, it should be done by next weekend. So since I'm very impatient all i do is think about the car. I was thinking about what else to get before i tune it so i don't have to be paying to do it over and over again. I'll let you guys now...
  15. JuanSTI

    METAL IN OIL PAN, LOW OIL PRESSURE AND CEL ???

    yea well its my fault in the first place for not taking care of it i was a horrible owner i took it for granted and here are the consequences. but now i'm more aware and learning a lot so it was going to happen sooner or later so now its up to me if i learn the lesson. also thank you guys for...
See more
Top